Fineline End Caps Pair
7 Working Day Delivery
UK Mainland Over £250
FREEFineline End Caps Pair
A pair of end caps designed to provide a neat, finished appearance at the ends of compatible Fineline track or profile installations. Specified where a clean termination detail is required for contract fit-out work.
Neat Finish
Closes off exposed ends for a clean detail
Practical Install
Simple component for finishing work
Supplied as a Pair
For completing both ends where required
Specifier Friendly
A defined finishing part for schedules
System Detail
Use with the intended Fineline components
Tidy Termination
Helps deliver a consistent end detail
Expectation setting: End caps are a finishing component. They do not provide blackout, privacy, or fire performance on their own. Compatibility can vary by Fineline system type—confirm the correct part for the track/profile being installed in the specification tab.
Overview
The Fineline End Caps Pair is intended to complete a Fineline installation by closing the track/profile ends and improving the finished appearance. It is commonly scheduled as a small but important detail on contract projects, helping the final installation look consistent and intentional.
Where multiple track runs are used, end caps support a clean, repeatable termination detail from room to room. For refurbishment work, they can also be used when replacing damaged or missing end caps to restore the original finish.
Any installation guidance, compatibility notes, and product confirmations are provided in the specification tab. If certificates or supporting documentation apply to this item, they are also supplied there.
Where this fits in our range
A finishing accessory for Fineline track/profile systems. Choose end caps where you need a neat termination detail and a consistent appearance across contract installations. For operating performance, specify the relevant track, brackets, runners, and stops separately where required.
Best suited for
- Contract fit-outs needing a clean, finished track/profile end detail
- Replacement of worn or missing end caps on existing Fineline systems
- Projects where consistent presentation matters (public-facing areas)
Who uses it
Specified by contractors, fit-out teams, and maintenance departments working on curtain track or window treatment installations. Typically used where a consistent finish is required across multiple rooms or where snagging items are being replaced.
Used in hospitality, healthcare, education, and general commercial interiors as part of a wider track or screening system schedule.
On-site clarification
For specification-critical work, confirm the Fineline system type and the required end detail before ordering. Installation guidance and any supporting documents are provided in the specification tab.
Technical specifications
| Product | Fineline End Caps Pair |
| Pack size | Pair (2 end caps) |
| Compatibility | Confirm correct Fineline system/type in the specification tab |
| Notes | Certificates, care/maintenance guidance, and any additional documentation are available in the specification tab |
Where applicable, installation guidance and supporting documents are provided in the specification tab to assist with scheduling and on-site checks.
| Delivery | 7 Working Day Delivery |
|---|
How do I place an order?
What payment methods do you accept?
What are your delivery times?
What is your returns policy?
Customer Product Reviews
Top customer reviews
-
A pleasure to do business with.Very easy to order after some helpful advice from the office and items partially dispatched and delivered as promised with a small part of the order still to come. Very good communication from them and a pleasure to deal with.0 people found this helpful
-
Great serviceAlana was super helpful and cert quick to answer any questions. Curtain (fineline) track arrived very quickly and although I haven't had time to install it yet, it looks fantastic, the hooks run very freely along the track which should make opening/closing the curtains much easier around a curved bay window.0 people found this helpful
How to Measure For Curtains, Blinds and Tracks.
Pen and Paper
For recording your
measurements.
Helper
Someone to assist if your
windows are large .
Metal Tape Measure
As this will allow you to get a
rigid full length measurement.
Make sure your curtain tracks and poles are fitted in the position you want.
Choose the type of curtains that you would like and how you want to hang your curtains. See our heading styles guide
We recommend fitting your hardware first before measuring, this avoids any issues with not getting the perfect fit.
Measure your window using our main guide. Quick summary below. Remember wave, pinch, and designer headings require slightly different measurement
Measure in 3 places and take the shortest drop – Floors and ceilings can run out.
Double / Triple check your measurements
Choosing your Curtain Track Width
The width of the curtain track should extend past your window this allows for the curtains to stack back away from your window and allow light in.
Measure your recess and then add on 15cm on either side. For acoustics , we recommend further to fully cover the window and the surrounding area. In our test we added an additional 30cm to the width and also made the curtain floor length.
Wave curtains, for every 100cm of track the curtains will stack circa *18cm
Eyelet curtains, they will stack back circa 10cm per *70cm of track width
Pencil Pleat will stack approx 25% of the track width. eg. 210cm track will stack 52.5%
* all dependent on thickness of fabric
Selecting your Curtain Drop
Where to Measure From for Different Type of Curtains
|
Type of Curtains |
Fitted On |
Where to Measure from - to desired length |
|
Pencil Pleat Curtains |
Curtain Track |
Top of the Track - If using a extra wide track or designer track like silent gliss metropole, then measure from the underside of the track. |
|
Pencil Pleat Curtains |
Curtain Pole |
Measure from small ring at the bottom of eye under the ring, this is where your curtain clips into. |
|
Eyelet Curtains |
Curtain Pole – Only |
Top of the pole *we add on the upstand to our curtains, |
|
Pinch Pleat Curtains |
Curtain Track |
The underside of the track |
|
Wave Curtains |
Curtain Track Designer Pole |
The glider underneath the track. The curtain will sit under the track. |
|
Acoustic Curtains |
See Heading Style of Choice above |
Same but make sure wider than normal ideally 30cm past either side and 30 above. Also to the floor. |
How to Measure for Blinds going Inside the Recess
- Measure the exact width of the recess in three places; at the top of the recess, in the centre of the recess and near the bottom - then take the smallest size.
- Measure the exact drop of the recess in three places on the left hand side of the recess, in the centre of the recess and on the right hand side of the recess - then take the smallest size.
- We will take one cm off the finished width size you have given us, to allow for the blind to pull up and down easily.
- Double check your measurements
- Cord Safety - Mounting Height - We ask for the mounting height of your blinds to allow for the cord to be 150cm off the ground. If mounting at 210cm This is what you enter in the Fitting height box. We make a deduction to ensure the cord is 150cm from the floor. Thus the cord loop will be 60cm
How to Measure Outside of the Recess
- Measure the recess in 3 places on the width and also 3 places on the drop. Take the widest measurement.
- Measure the width of the actual recess plus an additional amount – Usually from 7cm-15cm whatever you think looks appropriate. This is for overlap.
- Measure the exact drop of the recess. The blind would be fitted above the recess, so check the space above and add an amount on to the drop – usually from 7-15cm
- These sizes you have taken will be the size of the finished blind.
- Double check your measurements
- Cord Safety - Mounting Height - We ask for the mounting height of your blinds to allow for the cord to be 150cm off the ground. If mounting at 210cm This is what you enter in the fitting height box. We make a deduction to ensure the cord is 150cm from the floor. Thus the cord loop will be 60cm
Cubicle Tracks you have to measure with right angles from wall to wall where you want the track to go
Draw your room on a piece of paper with a sky view
Now measure from the wall to wall for straight tracks,
L Shape Tracks Measure to a point on the floor and mark with a piece of tape. Then for the other sides measure from the other wall to that point.
Always check for obstructions and fitting issues you may need to work around
SAVE TIME - Send your project requirements, large or small. Sample Lists etc