Flame Retardant Bedding | BS7175 Source 7 | Navy
Flame Retardant
Washable
Flame Retardant Bedding | BS7175 Source 7 | Navy
Flame Retardant
Washable
3 - 5 Working Days Delivery
UK Mainland Over £250
FREEFlame Retardant Bedding BS7175 Source 7 – Commercial Bed Linen (UK Manufactured)
UK-manufactured flame retardant bedding certified to BS7175 Source 7. Designed for higher-risk environments including care settings and custodial facilities, supplied directly from stock for fast dispatch.
BS7175 Source 7
Certified for higher-risk contract environments
Care Environment Suitable
Commonly specified in residential care settings
Custodial Approved
Labelled to BS7175 Source 7
Used Across NHS
Supplied into UK healthcare facilities
UK Manufactured
Made and stocked in the United Kingdom
Washable
Maintains flame retardant properties
Expectation setting: This is flame retardant contract bedding certified to BS7175 Source 7. It is designed for compliance and durability in commercial settings. It is not a decorative domestic bedding range.
BS7175 Source 7 Flame Retardant Bedding for Regulated Environments
Our flame retardant bedding is manufactured in the UK and certified to BS7175 Source 7, meeting the requirements for higher-risk residential and custodial settings.
Supplied directly from stock, this bedding is widely used across care homes, NHS facilities and secure accommodation where compliance is mandatory. Certification can be provided upon request.
The bedding is washable and designed to remain flame retardant in line with the standard. Full care guidance and documentation are available within the specification tab.
Where this fits in our range
This range sits within our higher-compliance bedding offer, intended for environments requiring BS7175 Source 7. For lower-risk accommodation, alternative ignition source ratings may be suitable.
Best suited for regulated commercial accommodation
Commonly specified for:
- Care homes and supported living accommodation
- NHS and healthcare facilities
- Prisons and custodial environments
- Youth hostels and regulated residential settings
- Ships and offshore accommodation
Suitable for organisations requiring clear labelling and compliance documentation under BS7175.
Technical specifications
| Fire Standard | BS7175 Source 7 |
| Manufacture | United Kingdom |
| Single Size | 137cm x 198cm (Envelope End)* |
| Certification | Certificate available on request |
*All sizes are approximate but designed to fit the stated mattress size. Full care instructions and compliance documentation are available within the specification tab or on request for tender purposes.
| Delivery | 3 - 5 Working Days Delivery |
|---|---|
| Washing / Cleaning Information Face Fabric | 71 Degress C |
| Fabric Style | Plains |
| Composition | 100% Inherent Flame Retardant Polyester |
| Flame Retardant | Yes |
| Flame Retardant Certified Rating | BS7175 Source 7 |
How do I care for and clean flame retardant curtains?
What does FR or flame retardant mean?
How to Measure for a Recess Fitted Blind
Customer Product Reviews
5.0
100% of customers recommend this product
Share your thoughts with other customers
Top customer reviews
-
Ordering was easyOrdering was easy , and my package came within a few days with everything I had ordered .0 people found this helpful
-
Alana Thomas she was was very fast and…Alana Thomas she was was very fast and good quoting us on time and dispatched it on same day.0 people found this helpful
-
Ordered late on Friday delivered by...Ordered late on Friday delivered by Tuesday. Great service0 people found this helpful
How to Measure For Curtains, Blinds and Tracks.
Pen and Paper
For recording your
measurements.
Helper
Someone to assist if your
windows are large .
Metal Tape Measure
As this will allow you to get a
rigid full length measurement.
Make sure your curtain tracks and poles are fitted in the position you want.
Choose the type of curtains that you would like and how you want to hang your curtains. See our heading styles guide
We recommend fitting your hardware first before measuring, this avoids any issues with not getting the perfect fit.
Measure your window using our main guide. Quick summary below. Remember wave, pinch, and designer headings require slightly different measurement
Measure in 3 places and take the shortest drop – Floors and ceilings can run out.
Double / Triple check your measurements
Choosing your Curtain Track Width
The width of the curtain track should extend past your window this allows for the curtains to stack back away from your window and allow light in.
Measure your recess and then add on 15cm on either side. For acoustics , we recommend further to fully cover the window and the surrounding area. In our test we added an additional 30cm to the width and also made the curtain floor length.
Wave curtains, for every 100cm of track the curtains will stack circa *18cm
Eyelet curtains, they will stack back circa 10cm per *70cm of track width
Pencil Pleat will stack approx 25% of the track width. eg. 210cm track will stack 52.5%
* all dependent on thickness of fabric
Selecting your Curtain Drop
Where to Measure From for Different Type of Curtains
|
Type of Curtains |
Fitted On |
Where to Measure from - to desired length |
|
Pencil Pleat Curtains |
Curtain Track |
Top of the Track - If using a extra wide track or designer track like silent gliss metropole, then measure from the underside of the track. |
|
Pencil Pleat Curtains |
Curtain Pole |
Measure from small ring at the bottom of eye under the ring, this is where your curtain clips into. |
|
Eyelet Curtains |
Curtain Pole – Only |
Top of the pole *we add on the upstand to our curtains, |
|
Pinch Pleat Curtains |
Curtain Track |
The underside of the track |
|
Wave Curtains |
Curtain Track Designer Pole |
The glider underneath the track. The curtain will sit under the track. |
|
Acoustic Curtains |
See Heading Style of Choice above |
Same but make sure wider than normal ideally 30cm past either side and 30 above. Also to the floor. |
How to Measure for Blinds going Inside the Recess
- Measure the exact width of the recess in three places; at the top of the recess, in the centre of the recess and near the bottom - then take the smallest size.
- Measure the exact drop of the recess in three places on the left hand side of the recess, in the centre of the recess and on the right hand side of the recess - then take the smallest size.
- We will take one cm off the finished width size you have given us, to allow for the blind to pull up and down easily.
- Double check your measurements
- Cord Safety - Mounting Height - We ask for the mounting height of your blinds to allow for the cord to be 150cm off the ground. If mounting at 210cm This is what you enter in the Fitting height box. We make a deduction to ensure the cord is 150cm from the floor. Thus the cord loop will be 60cm
How to Measure Outside of the Recess
- Measure the recess in 3 places on the width and also 3 places on the drop. Take the widest measurement.
- Measure the width of the actual recess plus an additional amount – Usually from 7cm-15cm whatever you think looks appropriate. This is for overlap.
- Measure the exact drop of the recess. The blind would be fitted above the recess, so check the space above and add an amount on to the drop – usually from 7-15cm
- These sizes you have taken will be the size of the finished blind.
- Double check your measurements
- Cord Safety - Mounting Height - We ask for the mounting height of your blinds to allow for the cord to be 150cm off the ground. If mounting at 210cm This is what you enter in the fitting height box. We make a deduction to ensure the cord is 150cm from the floor. Thus the cord loop will be 60cm
Cubicle Tracks you have to measure with right angles from wall to wall where you want the track to go
Draw your room on a piece of paper with a sky view
Now measure from the wall to wall for straight tracks,
L Shape Tracks Measure to a point on the floor and mark with a piece of tape. Then for the other sides measure from the other wall to that point.
Always check for obstructions and fitting issues you may need to work around
SAVE TIME - Send your project requirements, large or small. Sample Lists etc